| Author |
Message |
Mariusz
Guest
|
 Posted:
Fri Jul 08, 2005 8:10 am Post subject:
WildFire - coil modeling |
|
|
How to model the wire on the bobbin (coil). The bobbin section is quadratic.
|
|
| Back to top |
|
 |
Guest
|
| Posted:
Tue Jul 12, 2005 4:10 pm Post subject:
Re: WildFire - coil modeling |
|
|
I am not 100% what a bobbin coil is, try Helical Sweep or sweept blend.
Draw your 3d curve (quadradic) then draw your section. Constrain the
two and waaaalaaa.
Mariusz wrote:
> How to model the wire on the bobbin (coil). The bobbin section is quadratic. |
|
| Back to top |
|
|
LouR
Guest
|
| Posted:
Tue Jul 12, 2005 8:10 pm Post subject:
Adding a Relation to a Point |
|
|
I wonder if someone can help me out with this. I added a "point" to the
"Center of Gravity" in
my "assembly". as i work and add parts etc to my assembly i would like to
have this "point" i
added changed as the "center of gravity" changes. I like to make a relation
between this "point"
and the "center of gravity", anybody know how to do this??
thanks
LouR
|
|
| Back to top |
|
|
David Janes
Guest
|
| Posted:
Wed Jul 13, 2005 6:10 am Post subject:
Re: Adding a Relation to a Point |
|
|
| Quote: | "LouR" <russo1@bnl.gov> wrote
I wonder if someone can help me out with this. I added a "point" to the
"Center of Gravity" in
my "assembly". as i work and add parts etc to my assembly i would like to
have this "point" i
added changed as the "center of gravity" changes. I like to make a relation
between this "point"
and the "center of gravity", anybody know how to do this??
|
If the lab got you the good stuff, you can go to 'Insert>Model Datum>Analysis'. By
default, the type of analysis is set to the one you want - model analysis. Give
any name you want or leave the name as is. Then click the Next button. This looks
like the Model Analysis interface and it is. Only here, you can get out of it, not
just some text output. Here you can press, again, the Next button and go to Result
Params, such as XCOG, YCOG, ZCOG. When you click the Yes radio button to create
these, the COG values for x, y, and z are assigned to these parameters. Click next
again and go to Result Datums where you can elect to create either a result Center
of Gravity CSYS or datum point to visually identify, within your assembly, the
location of the center of mass. You can create both, if you wish, but you wished
for a point linked to the center of gravity and you've got it as a permanent,
analysis feature. If you want this to "run" at the end of the assembly regen,
select the ANALYSIS1, RMB 'Move to footer'. Now it will regen after you add a
component and give you an updated COG and an updated set of XCOG, etc parameters.
--
David Janes |
|
| Back to top |
|
|
LouR
Guest
|
| Posted:
Wed Jul 13, 2005 7:33 pm Post subject:
Re: Adding a Relation to a Point |
|
|
Thank you David for the Help!
=====================================
"David Janes" <djanes@cox.net.invawib> wrote in message
news:yTZAe.27748$4o.8730@fed1read06...
| Quote: | "LouR" <russo1@bnl.gov> wrote
I wonder if someone can help me out with this. I added a "point" to the
"Center of Gravity" in
my "assembly". as i work and add parts etc to my assembly i would like
to
have this "point" i
added changed as the "center of gravity" changes. I like to make a
relation
between this "point"
and the "center of gravity", anybody know how to do this??
If the lab got you the good stuff, you can go to 'Insert>Model
Datum>Analysis'. By
default, the type of analysis is set to the one you want - model analysis.
Give
any name you want or leave the name as is. Then click the Next button.
This looks
like the Model Analysis interface and it is. Only here, you can get out of
it, not
just some text output. Here you can press, again, the Next button and go
to Result
Params, such as XCOG, YCOG, ZCOG. When you click the Yes radio button to
create
these, the COG values for x, y, and z are assigned to these parameters.
Click next
again and go to Result Datums where you can elect to create either a
result Center
of Gravity CSYS or datum point to visually identify, within your assembly,
the
location of the center of mass. You can create both, if you wish, but you
wished
for a point linked to the center of gravity and you've got it as a
permanent,
analysis feature. If you want this to "run" at the end of the assembly
regen,
select the ANALYSIS1, RMB 'Move to footer'. Now it will regen after you
add a
component and give you an updated COG and an updated set of XCOG, etc
parameters.
--
David Janes
|
|
|
| Back to top |
|
|
|
|
|
|
FAQ
Memberlist
Register
Profile
Log in to check your private messages
Log in