| Author |
Message |
Dave Jones
Guest
|
 Posted:
Tue Nov 23, 2004 3:38 am Post subject:
Plotting .plt files |
|
|
I received some .plt files from an Architect and use Govert's GoPlot to plot
them to my HP1050C. These particular drawings are 42" x 30" but they are
plotting landscape from the plotter cutting off 6" of the width. Is there a
way to change the orientation of the plotted output or make a reduced size
copy?
Acad 2005, WinXP Pro, JetDirect networked HP1050C
thanks,
Dave
DDP
|
|
| Back to top |
|
 |
ToniG
Guest
|
| Posted:
Tue Nov 23, 2004 5:51 am Post subject:
Re: Plotting .plt files |
|
|
HI,
there are some viewer out there that allow you to open and print HPGL2
files.
Or you can use RIP...look at this very to use solution.....
http://www.tgsoft.ch/English/CADRIP.htm
It does autorotate the image, crop white image and also reduce if you want.
Many steps are done automaticly....
Regards
Toni
"Dave Jones" <spamless@nospam.com> schrieb im Newsbeitrag
news:41a26a4d$1_2@newsprd01...
| Quote: | I received some .plt files from an Architect and use Govert's GoPlot to
plot
them to my HP1050C. These particular drawings are 42" x 30" but they are
plotting landscape from the plotter cutting off 6" of the width. Is there
a
way to change the orientation of the plotted output or make a reduced size
copy?
Acad 2005, WinXP Pro, JetDirect networked HP1050C
thanks,
Dave
DDP
|
|
|
| Back to top |
|
|
Dave Jones
Guest
|
| Posted:
Tue Nov 23, 2004 6:01 am Post subject:
Re: Plotting .plt files |
|
|
thanks Toni, I'll check out RIP
Dave
"ToniG" <webmaster@NOSPAMtgsoft.ch> wrote in message
news:41a28a4b_2@newsprd01...
| Quote: | HI,
there are some viewer out there that allow you to open and print HPGL2
files.
Or you can use RIP...look at this very to use solution.....
http://www.tgsoft.ch/English/CADRIP.htm
It does autorotate the image, crop white image and also reduce if you
want.
Many steps are done automaticly....
Regards
Toni
"Dave Jones" <spamless@nospam.com> schrieb im Newsbeitrag
news:41a26a4d$1_2@newsprd01...
I received some .plt files from an Architect and use Govert's GoPlot to
plot
them to my HP1050C. These particular drawings are 42" x 30" but they are
plotting landscape from the plotter cutting off 6" of the width. Is
there
a
way to change the orientation of the plotted output or make a reduced
size
copy?
Acad 2005, WinXP Pro, JetDirect networked HP1050C
thanks,
Dave
DDP
|
|
|
| Back to top |
|
|
Dave Jones
Guest
|
| Posted:
Tue Nov 23, 2004 6:26 am Post subject:
Re: Plotting .plt files |
|
|
Toni,
did you get this app converted to English? If so, how?
Dave
"ToniG" <webmaster@NOSPAMtgsoft.ch> wrote in message
news:41a28a4b_2@newsprd01...
| Quote: | HI,
there are some viewer out there that allow you to open and print HPGL2
files.
Or you can use RIP...look at this very to use solution.....
http://www.tgsoft.ch/English/CADRIP.htm
It does autorotate the image, crop white image and also reduce if you
want.
Many steps are done automaticly....
Regards
Toni
"Dave Jones" <spamless@nospam.com> schrieb im Newsbeitrag
news:41a26a4d$1_2@newsprd01...
I received some .plt files from an Architect and use Govert's GoPlot to
plot
them to my HP1050C. These particular drawings are 42" x 30" but they are
plotting landscape from the plotter cutting off 6" of the width. Is
there
a
way to change the orientation of the plotted output or make a reduced
size
copy?
Acad 2005, WinXP Pro, JetDirect networked HP1050C
thanks,
Dave
DDP
|
|
|
| Back to top |
|
|
ToniG
Guest
|
| Posted:
Tue Nov 23, 2004 3:18 pm Post subject:
Re: Plotting .plt files |
|
|
Hello Dave,
in normal case, CADRIP should ask you on the fisrt run witsch language you
want...
However...it's is posible to switch to English, without re-installing.
I will send you a registry key by email.....with instructions....
Next time you start, the app run on English.
You also will find in the Install directory a PDF file
"CADRIP_Quick_guide_en.pdf".
This is a quick install and setup guide on English.
Just one thing...do you know that with CADRIP you can produce an E size
document at 600 DPI in ~ 2 Minutes ?
Just select "Draft" on speed, and be sure that in the configuration the
resolution is set to 600 DPI...easy....
If you have any question, please let us know.
Best regards
Toni Garamendi
"Dave Jones" <spamless@nospam.com> schrieb im Newsbeitrag
news:41a291a0_1@newsprd01...
| Quote: | Toni,
did you get this app converted to English? If so, how?
Dave
"ToniG" <webmaster@NOSPAMtgsoft.ch> wrote in message
news:41a28a4b_2@newsprd01...
HI,
there are some viewer out there that allow you to open and print HPGL2
files.
Or you can use RIP...look at this very to use solution.....
http://www.tgsoft.ch/English/CADRIP.htm
It does autorotate the image, crop white image and also reduce if you
want.
Many steps are done automaticly....
Regards
Toni
"Dave Jones" <spamless@nospam.com> schrieb im Newsbeitrag
news:41a26a4d$1_2@newsprd01...
I received some .plt files from an Architect and use Govert's GoPlot
to
plot
them to my HP1050C. These particular drawings are 42" x 30" but they
are
plotting landscape from the plotter cutting off 6" of the width. Is
there
a
way to change the orientation of the plotted output or make a reduced
size
copy?
Acad 2005, WinXP Pro, JetDirect networked HP1050C
thanks,
Dave
DDP
|
|
|
| Back to top |
|
|
Dave Jones
Guest
|
| Posted:
Tue Nov 23, 2004 7:50 pm Post subject:
Re: Plotting .plt files |
|
|
file received and my app is now in English. I was hoping to not have to
delve into my English/German dictionary :)
thanks!
Dave
"ToniG" <webmaster@NOSPAMtgsoft.ch> wrote in message
news:41a30f36$1_3@newsprd01...
| Quote: | Hello Dave,
in normal case, CADRIP should ask you on the fisrt run witsch language you
want...
However...it's is posible to switch to English, without re-installing.
I will send you a registry key by email.....with instructions....
Next time you start, the app run on English.
You also will find in the Install directory a PDF file
"CADRIP_Quick_guide_en.pdf".
This is a quick install and setup guide on English.
Just one thing...do you know that with CADRIP you can produce an E size
document at 600 DPI in ~ 2 Minutes ?
Just select "Draft" on speed, and be sure that in the configuration the
resolution is set to 600 DPI...easy....
If you have any question, please let us know.
Best regards
Toni Garamendi
"Dave Jones" <spamless@nospam.com> schrieb im Newsbeitrag
news:41a291a0_1@newsprd01...
Toni,
did you get this app converted to English? If so, how?
Dave
"ToniG" <webmaster@NOSPAMtgsoft.ch> wrote in message
news:41a28a4b_2@newsprd01...
HI,
there are some viewer out there that allow you to open and print HPGL2
files.
Or you can use RIP...look at this very to use solution.....
http://www.tgsoft.ch/English/CADRIP.htm
It does autorotate the image, crop white image and also reduce if you
want.
Many steps are done automaticly....
Regards
Toni
"Dave Jones" <spamless@nospam.com> schrieb im Newsbeitrag
news:41a26a4d$1_2@newsprd01...
I received some .plt files from an Architect and use Govert's GoPlot
to
plot
them to my HP1050C. These particular drawings are 42" x 30" but they
are
plotting landscape from the plotter cutting off 6" of the width. Is
there
a
way to change the orientation of the plotted output or make a
reduced
size
copy?
Acad 2005, WinXP Pro, JetDirect networked HP1050C
thanks,
Dave
DDP
|
|
|
| Back to top |
|
|
|
|
|
|
FAQ
Memberlist
Register
Profile
Log in to check your private messages
Log in