| Author |
Message |
Krister L
Guest
|
 Posted:
Fri Jan 07, 2005 12:55 pm Post subject:
Mass properties |
|
|
Hi Folks
I have a problem here with mass properties on edited SW materials. I have a
part template with material density set to 0.0078g/mm³ (stainless steel). In
some of these parts I added the SW material to get the real view graphic
display. I then regret this and removed that material without checking what
happened to the mass properties. If I now go back and have a look it's set
to 0.001g/mm³ (water) and I can't change it. My changes in the document
properties will not be accepted.
Is there anybody who has an idea about what to do? I normally use DbWorks to
set my materials and densities, but this one act just the same with DbW
unactivate.
SW Office 2005 Sp 0.1
|
|
| Back to top |
|
 |
Krister L
Guest
|
| Posted:
Fri Jan 07, 2005 1:21 pm Post subject:
Re: Mass properties |
|
|
This seems to be a bug (or something is changed which I messed) in SW 2005,
I just tried it on another computer in SW2004 and there it works, I can edit
the density in doc props after removing SW material, but opening the same
part again in SW 2005 Sp0.1 and do the same manoeuvre locks the density to 1
Krister L
"Krister L" <krister_landNOSPAMkvist@hotmail.com> wrote in message
news:346tjeF474cngU1@individual.net...
| Quote: | Hi Folks
I have a problem here with mass properties on edited SW materials. I have
a
part template with material density set to 0.0078g/mm³ (stainless steel).
In
some of these parts I added the SW material to get the real view graphic
display. I then regret this and removed that material without checking
what
happened to the mass properties. If I now go back and have a look it's set
to 0.001g/mm³ (water) and I can't change it. My changes in the document
properties will not be accepted.
Is there anybody who has an idea about what to do? I normally use DbWorks
to
set my materials and densities, but this one act just the same with DbW
unactivate.
SW Office 2005 Sp 0.1
|
|
|
| Back to top |
|
|
Krister L
Guest
|
| Posted:
Fri Jan 07, 2005 6:56 pm Post subject:
Re: Mass properties |
|
|
Bug verified and sent to SW for fix
/Krister L
"Krister L" <krister_landNOSPAMkvist@hotmail.com> wrote in message
news:346tjeF474cngU1@individual.net...
| Quote: | Hi Folks
I have a problem here with mass properties on edited SW materials. I have
a
part template with material density set to 0.0078g/mm³ (stainless steel).
In
some of these parts I added the SW material to get the real view graphic
display. I then regret this and removed that material without checking
what
happened to the mass properties. If I now go back and have a look it's set
to 0.001g/mm³ (water) and I can't change it. My changes in the document
properties will not be accepted.
Is there anybody who has an idea about what to do? I normally use DbWorks
to
set my materials and densities, but this one act just the same with DbW
unactivate.
SW Office 2005 Sp 0.1
|
|
|
| Back to top |
|
|
Wayne Tiffany
Guest
|
| Posted:
Fri Jan 07, 2005 10:09 pm Post subject:
Re: Mass properties |
|
|
I thought I was going crazy as I thought I had already run into this one.
So, I went back through my emails and found where I had submitted it to my
VAR on 9/16/04, but I don't think it made it to SW as I never did find a
reply. So, at least it's now in. Did you get an SPR number on it?
WT
"Krister L" <krister_landNOSPAMkvist@hotmail.com> wrote in message
news:346tjeF474cngU1@individual.net...
| Quote: | Hi Folks
I have a problem here with mass properties on edited SW materials. I have
a
part template with material density set to 0.0078g/mm³ (stainless steel).
In
some of these parts I added the SW material to get the real view graphic
display. I then regret this and removed that material without checking
what
happened to the mass properties. If I now go back and have a look it's set
to 0.001g/mm³ (water) and I can't change it. My changes in the document
properties will not be accepted.
Is there anybody who has an idea about what to do? I normally use DbWorks
to
set my materials and densities, but this one act just the same with DbW
unactivate.
SW Office 2005 Sp 0.1
|
|
|
| Back to top |
|
|
CS
Guest
|
| Posted:
Fri Jan 07, 2005 11:40 pm Post subject:
Re: Mass properties |
|
|
I think this had been discussed before. I don't remember exactly when but
within the last few months.
Corey
"Krister L" <krister_landNOSPAMkvist@hotmail.com> wrote in message
news:347ip5F482g1jU1@individual.net...
| Quote: | Bug verified and sent to SW for fix
/Krister L
"Krister L" <krister_landNOSPAMkvist@hotmail.com> wrote in message
news:346tjeF474cngU1@individual.net...
Hi Folks
I have a problem here with mass properties on edited SW materials. I
have
a
part template with material density set to 0.0078g/mm³ (stainless
steel).
In
some of these parts I added the SW material to get the real view graphic
display. I then regret this and removed that material without checking
what
happened to the mass properties. If I now go back and have a look it's
set
to 0.001g/mm³ (water) and I can't change it. My changes in the document
properties will not be accepted.
Is there anybody who has an idea about what to do? I normally use
DbWorks
to
set my materials and densities, but this one act just the same with DbW
unactivate.
SW Office 2005 Sp 0.1
|
|
|
| Back to top |
|
|
Krister L
Guest
|
| Posted:
Fri Jan 07, 2005 11:50 pm Post subject:
Re: Mass properties |
|
|
Nope, but got an answer from SW people here in Sweden later on today that it
should be fixed in Sp 1.0
/ Krister
"Wayne Tiffany" <wayne.tiffanyRMVJUNK@asi.com> skrev i meddelandet
news:347u30F475t7sU1@individual.net...
| Quote: | I thought I was going crazy as I thought I had already run into this one.
So, I went back through my emails and found where I had submitted it to my
VAR on 9/16/04, but I don't think it made it to SW as I never did find a
reply. So, at least it's now in. Did you get an SPR number on it?
WT
"Krister L" <krister_landNOSPAMkvist@hotmail.com> wrote in message
news:346tjeF474cngU1@individual.net...
Hi Folks
I have a problem here with mass properties on edited SW materials. I
have
a
part template with material density set to 0.0078g/mm³ (stainless
steel).
In
some of these parts I added the SW material to get the real view graphic
display. I then regret this and removed that material without checking
what
happened to the mass properties. If I now go back and have a look it's
set
to 0.001g/mm³ (water) and I can't change it. My changes in the document
properties will not be accepted.
Is there anybody who has an idea about what to do? I normally use
DbWorks
to
set my materials and densities, but this one act just the same with DbW
unactivate.
SW Office 2005 Sp 0.1
|
|
|
| Back to top |
|
|
Merry Owen
Guest
|
| Posted:
Sat Jan 08, 2005 6:59 pm Post subject:
Re: Mass properties |
|
|
I had this problem ages ago and reported it to my Var - he had no problems
as he changed the material properties using the material editor in the
Feature Manager, whilst I was trying to edit it using the document options
or with the mass properties options button.
Merry :-)
"Krister L" <krister_landNOSPAMkvist@hotmail.com> wrote in message
news:346tjeF474cngU1@individual.net...
| Quote: | Hi Folks
I have a problem here with mass properties on edited SW materials. I have
a
part template with material density set to 0.0078g/mm³ (stainless steel).
In
some of these parts I added the SW material to get the real view graphic
display. I then regret this and removed that material without checking
what
happened to the mass properties. If I now go back and have a look it's set
to 0.001g/mm³ (water) and I can't change it. My changes in the document
properties will not be accepted.
Is there anybody who has an idea about what to do? I normally use DbWorks
to
set my materials and densities, but this one act just the same with DbW
unactivate.
SW Office 2005 Sp 0.1
|
|
|
| Back to top |
|
|
|
|
|
|
FAQ
Memberlist
Register
Profile
Log in to check your private messages
Log in