| Author |
Message |
Jay Smith
Guest
|
 Posted:
Mon Aug 30, 2004 8:29 am Post subject:
Assura RCX error: *FATAL* at "rex": res command file error |
|
|
Dear all,
I got a problem while doing the parasitic ext for an op amp.
The complete amplifier layout was DRC clean and passed the LVS check.
I also did RCX extracation for all the sub-blocks of the op amp. The
extraction mode was set to "RC". Everything's fine. However, when I
tried to run RCX for the complete layout, I got the following errror:
*FATAL* at "rex": res command file error - imcomplete. (the last part
of the log file which shows this error was attached below). But if I
changed the extraction mode to parasitic capacitor only, I can
successfully get the ext done. Could anyone point where the problem
is? I'm running Cadence 5.0.33 with Assura 3.1. Thanks much!
Jay
*********************************************************
#==========================================================#
# Parasitic R extraction with default precision
#==========================================================#
rex -V -m -I'#' -u -N NET -e2 -rP res.mod np_rpoly::poly_cut \
np_rppoly::ppoly_cut np_rmetal1::mt1_cut np_rmetal2::mt2_cut \
np_rmetal3::mt3_cut np_rmetal4::mt4_cut np_rmetal5::mt5_cut \
np_rCTM5::ctm_cut np_rmetal6::mt6_cut - rVIA1,3,4,t rcv5,8,9,t \
rodCont_metal1_s_tndiff,3 rodCont_metal1_s_tpdiff,3 \
rodCont_metal1_tndiff,3 rodCont_metal1_tpdiff,3 \
rpl1co_metal1_poly,1,3,t rpl1co_metal1_ppoly,2,3,t \
rpl1co_ppoly_poly,1,2,t rtv2,4,5,t rtv3,5,6,t rtv4,6,7,t rtv5,7,9,t \
ND_bngate_MOS_619_mgvia,1,z PD_bpgate_MOS_771_mgvia,1,z \
NR_nrpop_RES_923_rvia,1,z LR_lrpop_RES_1055_rvia,1,z \
M5_capm5_CAP_1131_CTM5_cvia,8,z M5_capm5_CAP_1131_metal5_cvia,7,z - \
L1T0,3,I L2T0,4,I L3T0,5,I L4T0,6,I L5T0,7,I L6T0,9,I
*FATAL* at "rex": res command file error - imcomplete
*WARNING* Bad return status from RCX run. 0x1
*********************************************************
|
|
| Back to top |
|
 |
Erik Wanta
Guest
|
| Posted:
Thu Sep 02, 2004 2:23 pm Post subject:
Re: Assura RCX error: *FATAL* at "rex": res command file er |
|
|
Jay:
Are you running Assura 312 usr1?
---
Erik
mail9900@yahoo.com (Jay Smith) wrote in message news:<35c9712a.0408292029.5db88fdb@posting.google.com>...
| Quote: | Dear all,
I got a problem while doing the parasitic ext for an op amp.
The complete amplifier layout was DRC clean and passed the LVS check.
I also did RCX extracation for all the sub-blocks of the op amp. The
extraction mode was set to "RC". Everything's fine. However, when I
tried to run RCX for the complete layout, I got the following errror:
*FATAL* at "rex": res command file error - imcomplete. (the last part
of the log file which shows this error was attached below). But if I
changed the extraction mode to parasitic capacitor only, I can
successfully get the ext done. Could anyone point where the problem
is? I'm running Cadence 5.0.33 with Assura 3.1. Thanks much!
Jay
*********************************************************
#==========================================================#
# Parasitic R extraction with default precision
#==========================================================#
rex -V -m -I'#' -u -N NET -e2 -rP res.mod np_rpoly::poly_cut \
np_rppoly::ppoly_cut np_rmetal1::mt1_cut np_rmetal2::mt2_cut \
np_rmetal3::mt3_cut np_rmetal4::mt4_cut np_rmetal5::mt5_cut \
np_rCTM5::ctm_cut np_rmetal6::mt6_cut - rVIA1,3,4,t rcv5,8,9,t \
rodCont_metal1_s_tndiff,3 rodCont_metal1_s_tpdiff,3 \
rodCont_metal1_tndiff,3 rodCont_metal1_tpdiff,3 \
rpl1co_metal1_poly,1,3,t rpl1co_metal1_ppoly,2,3,t \
rpl1co_ppoly_poly,1,2,t rtv2,4,5,t rtv3,5,6,t rtv4,6,7,t rtv5,7,9,t \
ND_bngate_MOS_619_mgvia,1,z PD_bpgate_MOS_771_mgvia,1,z \
NR_nrpop_RES_923_rvia,1,z LR_lrpop_RES_1055_rvia,1,z \
M5_capm5_CAP_1131_CTM5_cvia,8,z M5_capm5_CAP_1131_metal5_cvia,7,z - \
L1T0,3,I L2T0,4,I L3T0,5,I L4T0,6,I L5T0,7,I L6T0,9,I
*FATAL* at "rex": res command file error - imcomplete
*WARNING* Bad return status from RCX run. 0x1
********************************************************* |
|
|
| Back to top |
|
|
Andrew Beckett
Guest
|
| Posted:
Thu Sep 02, 2004 2:59 pm Post subject:
Re: Assura RCX error: *FATAL* at "rex": res command file er |
|
|
I spoke with Jay off line (he emailed me directly) and he isn't using 312USR1 -
I advised that, as I found some similar problems in 312 (which is what he is
using).
Andrew.
On 2 Sep 2004 03:23:57 -0700, erikwanta@starband.net (Erik Wanta) wrote:
| Quote: | Jay:
Are you running Assura 312 usr1?
---
Erik
mail9900@yahoo.com (Jay Smith) wrote in message news:<35c9712a.0408292029.5db88fdb@posting.google.com>...
Dear all,
I got a problem while doing the parasitic ext for an op amp.
The complete amplifier layout was DRC clean and passed the LVS check.
I also did RCX extracation for all the sub-blocks of the op amp. The
extraction mode was set to "RC". Everything's fine. However, when I
tried to run RCX for the complete layout, I got the following errror:
*FATAL* at "rex": res command file error - imcomplete. (the last part
of the log file which shows this error was attached below). But if I
changed the extraction mode to parasitic capacitor only, I can
successfully get the ext done. Could anyone point where the problem
is? I'm running Cadence 5.0.33 with Assura 3.1. Thanks much!
Jay
*********************************************************
#==========================================================#
# Parasitic R extraction with default precision
#==========================================================#
rex -V -m -I'#' -u -N NET -e2 -rP res.mod np_rpoly::poly_cut \
np_rppoly::ppoly_cut np_rmetal1::mt1_cut np_rmetal2::mt2_cut \
np_rmetal3::mt3_cut np_rmetal4::mt4_cut np_rmetal5::mt5_cut \
np_rCTM5::ctm_cut np_rmetal6::mt6_cut - rVIA1,3,4,t rcv5,8,9,t \
rodCont_metal1_s_tndiff,3 rodCont_metal1_s_tpdiff,3 \
rodCont_metal1_tndiff,3 rodCont_metal1_tpdiff,3 \
rpl1co_metal1_poly,1,3,t rpl1co_metal1_ppoly,2,3,t \
rpl1co_ppoly_poly,1,2,t rtv2,4,5,t rtv3,5,6,t rtv4,6,7,t rtv5,7,9,t \
ND_bngate_MOS_619_mgvia,1,z PD_bpgate_MOS_771_mgvia,1,z \
NR_nrpop_RES_923_rvia,1,z LR_lrpop_RES_1055_rvia,1,z \
M5_capm5_CAP_1131_CTM5_cvia,8,z M5_capm5_CAP_1131_metal5_cvia,7,z - \
L1T0,3,I L2T0,4,I L3T0,5,I L4T0,6,I L5T0,7,I L6T0,9,I
*FATAL* at "rex": res command file error - imcomplete
*WARNING* Bad return status from RCX run. 0x1
*********************************************************
|
--
Andrew Beckett
Senior Technical Leader
Custom IC Solutions
Cadence Design Systems Ltd
|
|
| Back to top |
|
|
Bernd Fischer
Guest
|
| Posted:
Thu Sep 02, 2004 3:38 pm Post subject:
Re: Assura RCX error: *FATAL* at "rex": res command file er |
|
|
Erik Wanta wrote:
| Quote: | Jay:
Are you running Assura 312 usr1?
|
Dear Andrew, dear Erik,
Is there something to say about 3.12 USR1,
I was to install it very soon?
Bernd |
|
| Back to top |
|
|
Andrew Beckett
Guest
|
| Posted:
Fri Sep 03, 2004 7:00 am Post subject:
Re: Assura RCX error: *FATAL* at "rex": res command file er |
|
|
Bernd,
I don't understand what you're asking here.
Andrew.
On Thu, 02 Sep 2004 13:38:22 +0200, Bernd Fischer
<""bernd.fischer\"@xignal-A%&HY%$v#&G=.de> wrote:
| Quote: |
Erik Wanta wrote:
Jay:
Are you running Assura 312 usr1?
Dear Andrew, dear Erik,
Is there something to say about 3.12 USR1,
I was to install it very soon?
Bernd
|
--
Andrew Beckett
Senior Technical Leader
Custom IC Solutions
Cadence Design Systems Ltd |
|
| Back to top |
|
|
Erik Wanta
Guest
|
| Posted:
Fri Sep 03, 2004 8:23 pm Post subject:
Re: Assura RCX error: *FATAL* at "rex": res command file er |
|
|
Bernd:
We had several RCX problems with the base 312 release that are fixed
in the 312 USR1 release. I would recommend you move to the 312 USR1
release and hopefully your problem will disappear.
---
Erik
Andrew Beckett <andrewb@DELETETHISBITcadence.com> wrote in message news:<0hnfj09mqbv694sjbe44lkicg2c7uf17n8@4ax.com>...
| Quote: | Bernd,
I don't understand what you're asking here.
Andrew.
On Thu, 02 Sep 2004 13:38:22 +0200, Bernd Fischer
""bernd.fischer\"@xignal-A%&HY%$v#&G=.de> wrote:
Erik Wanta wrote:
Jay:
Are you running Assura 312 usr1?
Dear Andrew, dear Erik,
Is there something to say about 3.12 USR1,
I was to install it very soon?
Bernd |
|
|
| Back to top |
|
|
|
|
|
|
FAQ
Memberlist
Register
Profile
Log in to check your private messages
Log in