| Author |
Message |
bstaples
Guest
|
 Posted:
Thu Oct 28, 2004 6:58 pm Post subject:
using Group Policy to assign an installation |
|
|
Has anyone had any luck with using AD and group policy to assign an installation and been successful? I have read through the networking admin guide, section C pages 69-74. I have done the exact steps but when I reboot a target station, I see quickly a message about ADT2005 beginning to setup but then it's finished after a few seconds and the logon screen appears. I log in but there is no icon to click on as specified on page 74.
In the event viewer application management errors are recorded. One will say "failed to apply changes to software installation settings, software changes could not be applied" The other says "The install of application ADT2005 from policy failed. The error was: The install source is not available, check the source exists and you can access it"
I can then connect to the server where the deployment resides and I can see get into the folders fine. The only thing preventing me from going further is when I try to run the deployment it tells me I need admin rights.
I would appreciate any insight to this as I would love to be able to assign the installs to new workstations without having to give users any extra rights to run installs.
Brian
|
|
| Back to top |
|
 |
jerry milana (Autodesk Co
Guest
|
| Posted:
Thu Oct 28, 2004 10:52 pm Post subject:
Re: using Group Policy to assign an installation |
|
|
Your users should not need administrative rights to their workstations. I
suspect an access problem. I would start by allowing full control of the
location where the deployment resides and its subfolders to everyone. If
that helps then you can experiment on locking the folder down a bit.
--
Jerry Milana,
Autodesk Consulting
"bstaples" <nospam@address.withheld> wrote in message
news:3307044.1098975528373.JavaMail.jive@jiveforum2.autodesk.com...
| Quote: | Has anyone had any luck with using AD and group policy to assign an
installation and been successful? I have read through the networking admin |
guide, section C pages 69-74. I have done the exact steps but when I reboot
a target station, I see quickly a message about ADT2005 beginning to setup
but then it's finished after a few seconds and the logon screen appears. I
log in but there is no icon to click on as specified on page 74.
| Quote: |
In the event viewer application management errors are recorded. One will
say "failed to apply changes to software installation settings, software |
changes could not be applied" The other says "The install of application
ADT2005 from policy failed. The error was: The install source is not
available, check the source exists and you can access it"
| Quote: |
I can then connect to the server where the deployment resides and I can
see get into the folders fine. The only thing preventing me from going |
further is when I try to run the deployment it tells me I need admin rights.
| Quote: |
I would appreciate any insight to this as I would love to be able to
assign the installs to new workstations without having to give users any |
extra rights to run installs.
|
|
| Back to top |
|
|
Juha Hänninen
Guest
|
| Posted:
Fri Oct 29, 2004 2:25 pm Post subject:
Re: using Group Policy to assign an installation |
|
|
Yes,
the GPO installs the .msi packages with system rights.
I'm not sure about ADT2005, I only have installed AutoCAD2005 with GPO.
There the problem was at first that 2005 need .NET Framework installed
before it will install. Dotnet.exe can be downloaded from Microsoft and
extracted, inside is netfx.msi and netfx1.cab. We installed them with GPO
and after that the 2005 installation also succeeded.
For our own modifications we made a .msi. We also made a .msi of the AutoCAD
files in user cache that are normally copied under each profile and
installed them under AutoCAD so that they are always in standard locations.
Juha
"bstaples" <nospam@address.withheld> wrote in message
news:3307044.1098975528373.JavaMail.jive@jiveforum2.autodesk.com...
| Quote: | Has anyone had any luck with using AD and group policy to assign an
installation and been successful? I have read through the networking admin |
guide, section C pages 69-74. I have done the exact steps but when I reboot
a target station, I see quickly a message about ADT2005 beginning to setup
but then it's finished after a few seconds and the logon screen appears. I
log in but there is no icon to click on as specified on page 74.
| Quote: |
In the event viewer application management errors are recorded. One will
say "failed to apply changes to software installation settings, software |
changes could not be applied" The other says "The install of application
ADT2005 from policy failed. The error was: The install source is not
available, check the source exists and you can access it"
| Quote: |
I can then connect to the server where the deployment resides and I can
see get into the folders fine. The only thing preventing me from going |
further is when I try to run the deployment it tells me I need admin rights.
| Quote: |
I would appreciate any insight to this as I would love to be able to
assign the installs to new workstations without having to give users any |
extra rights to run installs.
|
|
| Back to top |
|
|
Thomas Nussrallah
Guest
|
| Posted:
Tue Nov 02, 2004 4:30 am Post subject:
Re: using Group Policy to assign an installation |
|
|
Brian,
I would focus in on the "install source is not available" error. When you
built the GPO that contains the software deployment, to where did you browse
to find the msi file? If that path is local to that server (that is, if it
starts with "C:\" or "D:\"), the installs will fail with this error. The
path to the msi must be in UNC format (\\server\share\).
Tom N.
"bstaples" <nospam@address.withheld> wrote in message
news:3307044.1098975528373.JavaMail.jive@jiveforum2.autodesk.com...
| Quote: | Has anyone had any luck with using AD and group policy to assign an
installation and been successful? I have read through the networking admin
guide, section C pages 69-74. I have done the exact steps but when I
reboot a target station, I see quickly a message about ADT2005 beginning
to setup but then it's finished after a few seconds and the logon screen
appears. I log in but there is no icon to click on as specified on page
74.
In the event viewer application management errors are recorded. One will
say "failed to apply changes to software installation settings, software
changes could not be applied" The other says "The install of application
ADT2005 from policy failed. The error was: The install source is not
available, check the source exists and you can access it"
I can then connect to the server where the deployment resides and I can
see get into the folders fine. The only thing preventing me from going
further is when I try to run the deployment it tells me I need admin
rights.
I would appreciate any insight to this as I would love to be able to
assign the installs to new workstations without having to give users any
extra rights to run installs.
Brian |
|
|
| Back to top |
|
|
|
|
|
|
FAQ
Memberlist
Register
Profile
Log in to check your private messages
Log in