| Author |
Message |
vivian
Guest
|
 Posted:
Tue Nov 08, 2005 1:10 am Post subject:
Question about Ocean command |
|
|
When I run the simulation in Ocean, the command "run" always gives
error:
Syntax error in "input.scs".
I checked "input.scs", this is a file created when doing the
simulation. And the error is in the last line.
But there is only "// " in last line. what is wrong with it?
The procedure of my simulation:
created psf in spectre.
Then open the ocean command line.
->ocean simulator('spectre)
->ocean design("/.../..../netlist")
->ocean analysis('tran ?stop 100n)
->ocean run
Then the error comes..
|
|
| Back to top |
|
 |
Svenn Are Bjerkem
Guest
|
| Posted:
Tue Nov 08, 2005 9:10 am Post subject:
Re: Question about Ocean command |
|
|
In article <1131401399.605156.276010@g43g2000cwa.googlegroups.com>,
wangllu@yahoo.com says...
| Quote: | I checked "input.scs", this is a file created when doing the
simulation. And the error is in the last line.
But there is only "// " in last line. what is wrong with it?
|
My experience from other file-input simulators is that there must be a
linefeed at the end of the file. Some programs (I think emacs) do not
explicitly insert a linefeed at the end of the file and then the input
routine of the simulator is failing.
I would try to insert an extra push of the enter key at the end of the
file and resimulate.
--
Svenn |
|
| Back to top |
|
|
vivian
Guest
|
| Posted:
Tue Nov 08, 2005 5:10 pm Post subject:
Re: Question about Ocean command |
|
|
Thank you for your information.
The netlist is created by system, not me. How can I control what will
be input into the file?
|
|
| Back to top |
|
|
S. Badel
Guest
|
| Posted:
Tue Nov 08, 2005 9:10 pm Post subject:
Re: Question about Ocean command |
|
|
If there's an error on the last line, it might be that something was
expected to happen but was not found before the end of the file.
I expect that there's a real error in your netlist, and if you find
this error you'll be able to trace it to its source.
I notice that you are giving the netlist, the error might well be in your
netlist. input.scs is a file created which includes the netlist you provide
as well as analysis statements, includes, etc that you tell ocean to insert.
I can not say anymore with the data you provided,
Stéphane
vivian wrote:
| Quote: | When I run the simulation in Ocean, the command "run" always gives
error:
Syntax error in "input.scs".
I checked "input.scs", this is a file created when doing the
simulation. And the error is in the last line.
But there is only "// " in last line. what is wrong with it?
The procedure of my simulation:
created psf in spectre.
Then open the ocean command line.
->ocean simulator('spectre)
->ocean design("/.../..../netlist")
->ocean analysis('tran ?stop 100n)
->ocean run
Then the error comes..
|
|
|
| Back to top |
|
|
Andrew Beckett
Guest
|
| Posted:
Thu Nov 10, 2005 1:10 am Post subject:
Re: Question about Ocean command |
|
|
I was going to make a similar comment to Stephane - you don't give the precise
error message - nor the affected segment of the netlist. Without seeing this,
there's little chance of debugging the error. Perhaps it's the last real line
before the end of the input.scs which has the error - perhaps the command is
incomplete?
Can you:
a) post the actual error message given
b) post the last few lines from the input.scs - i.e. from the analysis
statements to the end of file.
This will probably help us figure out what's wrong.
Regards,
Andrew.
On Tue, 08 Nov 2005 18:19:28 +0100, "S. Badel"
<stephane.badel@REMOVETHISepfl.ch> wrote:
| Quote: | If there's an error on the last line, it might be that something was
expected to happen but was not found before the end of the file.
I expect that there's a real error in your netlist, and if you find
this error you'll be able to trace it to its source.
I notice that you are giving the netlist, the error might well be in your
netlist. input.scs is a file created which includes the netlist you provide
as well as analysis statements, includes, etc that you tell ocean to insert.
I can not say anymore with the data you provided,
Stéphane
vivian wrote:
When I run the simulation in Ocean, the command "run" always gives
error:
Syntax error in "input.scs".
I checked "input.scs", this is a file created when doing the
simulation. And the error is in the last line.
But there is only "// " in last line. what is wrong with it?
The procedure of my simulation:
created psf in spectre.
Then open the ocean command line.
->ocean simulator('spectre)
->ocean design("/.../..../netlist")
->ocean analysis('tran ?stop 100n)
->ocean run
Then the error comes..
|
|
|
| Back to top |
|
|
|
|
|
|
FAQ
Memberlist
Register
Profile
Log in to check your private messages
Log in