| Author |
Message |
Pat
Guest
|
 Posted:
Wed Oct 26, 2005 8:10 pm Post subject:
Mechanical design consulting - what's the going rate? |
|
|
Hello all,
I'm working on a proposal which, if funded, will involve a considerable
amount of mechanical design work (solid modeling, etc.). Although I plan to
do some of it myself, I will clearly need some help with this.
At this point I'm just trying to estimate how much cost to allow for the
consultants time. I've come up with an estimate of the number hours I think
I'll need them for, but what I'm not sure about is an hourly rate. Does
anyone have any idea what a typical rate (or range) would be for a good
mechanical design consultant (preferably someone with an engineering
degree)?
Also, if this gets funded (which I think is likely) what would be the best
way locate someone? Although I'm located in the midwest (near Louisville,
KY) I'm not sure it's that critical (if at all) that the person be located
nearby. With the web and email a lot can be done remotely these days. Are
there websites where people post for work like this?
Thanks for any help or advice. I appreciate it.
Pat
|
|
| Back to top |
|
 |
matt
Guest
|
| Posted:
Wed Oct 26, 2005 8:10 pm Post subject:
Re: Mechanical design consulting - what's the going rate? |
|
|
The low end of design work starts about $50/hr, more commonly at $75 -
150, depending on if you're going direct to an individual contractor,
through a real engineering firm or a placement agency. Engineering
analysis (FEA, motion studies, etc) can go pretty high, say $200/hr,
depending on where you go.
The best way to locate someone is word of mouth, if you know other
people or companies who have used individuals or organizations for work.
You can also look through the SolidWorks website for the Mfg Network,
where there are tons of SolidWorks using companies who can help you out.
Good luck,
Matt
www.dezignstuff.com
In article <jkQ7f.477897$_o.309393@attbi_s71>, "Pat" <pkelecy
(removethis)@insightbb.com> says...
| Quote: | Hello all,
I'm working on a proposal which, if funded, will involve a considerable
amount of mechanical design work (solid modeling, etc.). Although I plan to
do some of it myself, I will clearly need some help with this.
At this point I'm just trying to estimate how much cost to allow for the
consultants time. I've come up with an estimate of the number hours I think
I'll need them for, but what I'm not sure about is an hourly rate. Does
anyone have any idea what a typical rate (or range) would be for a good
mechanical design consultant (preferably someone with an engineering
degree)?
Also, if this gets funded (which I think is likely) what would be the best
way locate someone? Although I'm located in the midwest (near Louisville,
KY) I'm not sure it's that critical (if at all) that the person be located
nearby. With the web and email a lot can be done remotely these days. Are
there websites where people post for work like this?
Thanks for any help or advice. I appreciate it.
Pat
|
|
|
| Back to top |
|
|
John Eric Voltin
Guest
|
| Posted:
Thu Oct 27, 2005 8:10 am Post subject:
Re: Mechanical design consulting - what's the going rate? |
|
|
Matt's nice summary is consistent with my experience in Central Texas. My
company provides engineering and design services at $65 per hour, but we
have very low overhead and don't have the cost of a centralized office. We
all work out of home offices.
--
- John
John Eric Voltin
Mechanical Engineer
Agile Technology
512-633-0394
"matt" <m_lombard@ver_zon.not> wrote in message
news:MPG.1dc9aab8a5d6854f989728@news.verizon.net...
| Quote: | The low end of design work starts about $50/hr, more commonly at $75 -
150, depending on if you're going direct to an individual contractor,
through a real engineering firm or a placement agency. Engineering
analysis (FEA, motion studies, etc) can go pretty high, say $200/hr,
depending on where you go.
The best way to locate someone is word of mouth, if you know other
people or companies who have used individuals or organizations for work.
You can also look through the SolidWorks website for the Mfg Network,
where there are tons of SolidWorks using companies who can help you out.
Good luck,
Matt
www.dezignstuff.com
In article <jkQ7f.477897$_o.309393@attbi_s71>, "Pat" <pkelecy
(removethis)@insightbb.com> says...
Hello all,
I'm working on a proposal which, if funded, will involve a considerable
amount of mechanical design work (solid modeling, etc.). Although I plan
to
do some of it myself, I will clearly need some help with this.
At this point I'm just trying to estimate how much cost to allow for the
consultants time. I've come up with an estimate of the number hours I
think
I'll need them for, but what I'm not sure about is an hourly rate. Does
anyone have any idea what a typical rate (or range) would be for a good
mechanical design consultant (preferably someone with an engineering
degree)?
Also, if this gets funded (which I think is likely) what would be the
best
way locate someone? Although I'm located in the midwest (near
Louisville,
KY) I'm not sure it's that critical (if at all) that the person be
located
nearby. With the web and email a lot can be done remotely these days.
Are
there websites where people post for work like this?
Thanks for any help or advice. I appreciate it.
Pat
|
|
|
| Back to top |
|
|
Cliff
Guest
|
| Posted:
Thu Oct 27, 2005 8:10 am Post subject:
Re: Mechanical design consulting - what's the going rate? |
|
|
On Thu, 27 Oct 2005 19:23:13 +1300, John Layne
<JohnDON'TBUGMEWITHSPAM@solidengineering.co.nz> wrote:
| Quote: | Cost of living in New Zealand is somewhat cheaper
|
Mutton prices <G>?
--
Cliff |
|
| Back to top |
|
|
John Layne
Guest
|
| Posted:
Thu Oct 27, 2005 8:10 am Post subject:
Re: Mechanical design consulting - what's the going rate? |
|
|
Pat wrote:
| Quote: | Hello all,
I'm working on a proposal which, if funded, will involve a considerable
amount of mechanical design work (solid modeling, etc.). Although I plan to
do some of it myself, I will clearly need some help with this.
At this point I'm just trying to estimate how much cost to allow for the
consultants time. I've come up with an estimate of the number hours I think
I'll need them for, but what I'm not sure about is an hourly rate. Does
anyone have any idea what a typical rate (or range) would be for a good
mechanical design consultant (preferably someone with an engineering
degree)?
Also, if this gets funded (which I think is likely) what would be the best
way locate someone? Although I'm located in the midwest (near Louisville,
KY) I'm not sure it's that critical (if at all) that the person be located
nearby. With the web and email a lot can be done remotely these days. Are
there websites where people post for work like this?
Thanks for any help or advice. I appreciate it.
Pat
|
I and my associates charge between $80 and $120 New Zealand dollars per
hour depending on work type and quantity. That about $55 to $83 in USA
dollars a year ago that would have been around $45US
Cost of living in New Zealand is somewhat cheaper hence the low rates.
John Layne
www.solidengineering.co.nz |
|
| Back to top |
|
|
matt
Guest
|
| Posted:
Thu Oct 27, 2005 4:10 pm Post subject:
Re: Mechanical design consulting - what's the going rate? |
|
|
| Quote: | ... how well does it work
to have two (or more) people working together on, say, part models for the
same assembly or device, particularly when the designers are remotely
located? Logistically it seems like there could be some challenging issues
(like where part files are kept, coordinating interface designs, file
compatibility, etc.). Any thoughts or advice?
|
90% of the work I do is remote. Generally things work out best when you
have the work well laid out, which generally for me means bulleted lists
of tasks or goals, and visual markups of concepts which are awkward in
to convey in words. eDrawings are a great way to do this to show 3D
geometry, but I often use screen captures in Powerpoint with circles,
arrows and annotations.
Communication is really key, but that's the case whether your designers
are remote or in the next cube.
In terms of using multiple remote designers, that can be a challenge. I
would try to separate the work in such a way that each person's work is
as self contained as possible.
Start by specifying:
- version of the software to be used (2005 vs 2006),
- how or if Toolbox is to be used, or maybe make available an existing
hardware library
- general modeling standards, such as the use of incontext features,
mirrored parts, base parts, multibody, under defined sketches, tolerance
for cherries in the tree, dynamic motion in the assembly, etc
- filenaming conventions so you don't have name conflicts
- an effective way of handling revisions. I would recommend keeping
file names the same, but putting revision levels in the name of a zip
file which is transferred via FTP
- boundary conditions ("your design starts at this 2" knuckle and
extends to the 1/2" bolted connection on this end of the frame. leave
clearance for this kind of motion...")
matt |
|
| Back to top |
|
|
Pat
Guest
|
| Posted:
Thu Oct 27, 2005 4:10 pm Post subject:
Re: Mechanical design consulting - what's the going rate? |
|
|
Thanks to everyone for the responses (especially Matt for the nice summary).
This gives me a good idea of what to allow for labor cost.
One other question. In your experiences doing this, how well does it work
to have two (or more) people working together on, say, part models for the
same assembly or device, particularly when the designers are remotely
located? Logistically it seems like there could be some challenging issues
(like where part files are kept, coordinating interface designs, file
compatibility, etc.). Any thoughts or advice?
Thanks again. -Pat |
|
| Back to top |
|
|
Ken
Guest
|
| Posted:
Thu Oct 27, 2005 4:10 pm Post subject:
Re: Mechanical design consulting - what's the going rate? |
|
|
I am inexperienced in this type of thing, but additional questions I would
have would pertain to my liability in the design work such as: is it
necessary to have a PE stamp, do I need liability insurance to cover my @$$
if I or someone working for me makes a mistake or if the client is just a
litigious freak.
Ken
"Pat" <pkelecy(removethis)@insightbb.com> wrote in message
news:jkQ7f.477897$_o.309393@attbi_s71...
| Quote: | Hello all,
I'm working on a proposal which, if funded, will involve a considerable
amount of mechanical design work (solid modeling, etc.). Although I plan
to do some of it myself, I will clearly need some help with this.
At this point I'm just trying to estimate how much cost to allow for the
consultants time. I've come up with an estimate of the number hours I
think I'll need them for, but what I'm not sure about is an hourly rate.
Does anyone have any idea what a typical rate (or range) would be for a
good mechanical design consultant (preferably someone with an engineering
degree)?
Also, if this gets funded (which I think is likely) what would be the best
way locate someone? Although I'm located in the midwest (near Louisville,
KY) I'm not sure it's that critical (if at all) that the person be located
nearby. With the web and email a lot can be done remotely these days.
Are there websites where people post for work like this?
Thanks for any help or advice. I appreciate it.
Pat
|
|
|
| Back to top |
|
|
John Layne
Guest
|
| Posted:
Thu Oct 27, 2005 8:10 pm Post subject:
Re: Mechanical design consulting - what's the going rate? |
|
|
Pat wrote:
| Quote: | Thanks to everyone for the responses (especially Matt for the nice summary).
This gives me a good idea of what to allow for labor cost.
One other question. In your experiences doing this, how well does it work
to have two (or more) people working together on, say, part models for the
same assembly or device, particularly when the designers are remotely
located? Logistically it seems like there could be some challenging issues
(like where part files are kept, coordinating interface designs, file
compatibility, etc.). Any thoughts or advice?
Thanks again. -Pat
|
Matt summed it up very well, as usual.
I'm currently working remotely for several clients and have set up an
ftp server specifically for this.
Edrawings are a great way to communicate and I also set up my SolidWorks
PC to allow remote access via TightVNC. Clients can view the model as I
work on it or they can take control while we are discussing the model
over the phone. All the client needs for TightVNC to work is to have
Java installed on there PC.
John Layne
www.solidengineering.co.nz |
|
| Back to top |
|
|
Pat
Guest
|
| Posted:
Fri Oct 28, 2005 4:10 pm Post subject:
Re: Mechanical design consulting - what's the going rate? |
|
|
Thanks Matt and John for the additional information.
I agree that good communication and organization is important regardless of
the work arrangement, but probably even more so when working remotely.
I was particularly interested in the logistical issues of this - how well
ftp-ing large CAD files back and forth and keeping related designs
coordinated works in practice. Apparently well enough.
Out of curiosity, is doing such CAD work over a terminal server connection,
such a VNC or Microsoft's RDC, a practical option (where Solidworks would be
running on the remote computer)? Although I'm sure it can be done, I'm not
sure what the user experience would be like. It would, however, keep all
the files together and avoid the need to ftp.
Thanks again.
Pat
"John Layne" <JohnDON'TBUGMEWITHSPAM@solidengineering.co.nz> wrote in
message news:Ek88f.3029$S24.201653@news.xtra.co.nz...
| Quote: | Pat wrote:
Thanks to everyone for the responses (especially Matt for the nice
summary). This gives me a good idea of what to allow for labor cost.
One other question. In your experiences doing this, how well does it
work to have two (or more) people working together on, say, part models
for the same assembly or device, particularly when the designers are
remotely located? Logistically it seems like there could be some
challenging issues (like where part files are kept, coordinating
interface designs, file compatibility, etc.). Any thoughts or advice?
Thanks again. -Pat
Matt summed it up very well, as usual.
I'm currently working remotely for several clients and have set up an ftp
server specifically for this.
Edrawings are a great way to communicate and I also set up my SolidWorks
PC to allow remote access via TightVNC. Clients can view the model as I
work on it or they can take control while we are discussing the model over
the phone. All the client needs for TightVNC to work is to have Java
installed on there PC.
John Layne
www.solidengineering.co.nz |
|
|
| Back to top |
|
|
Sporkman
Guest
|
| Posted:
Fri Oct 28, 2005 4:10 pm Post subject:
Re: Mechanical design consulting - what's the going rate? |
|
|
Ken wrote:
| Quote: |
I am inexperienced in this type of thing, but additional questions I would
have would pertain to my liability in the design work such as: is it
necessary to have a PE stamp, do I need liability insurance to cover my @$$
if I or someone working for me makes a mistake or if the client is just a
litigious freak.
Ken
|
These are certainly concerns when acting as a consultant, but attorneys
have told me that as long you're incorporated and the corporation has an
easily definable list of assets there is little danger of losing
anything other than those assets. Certain situations exacerbate
potential danger -- for instance, unless you are both a PE AND you keep
very careful engineering notebooks you should stay away from stuctural
design, especially that which incorporates human elements where humans
could be injured if a structure fails. Also, be concervative about
product design when the product itself could produce injurious results.
I've turned away several potential clients recently for this reason.
One wanted to design a special underwater breathing apparatus for
general public consumption -- definitely a red flag. One simply has to
ask oneself how you might conceivably end up liable. We live in a very
litigious society, but you really don't need to lose any sleep over
designing a new soap dispenser.
'Sporky'
www.h2omarkdesign.com |
|
| Back to top |
|
|
matt
Guest
|
| Posted:
Fri Oct 28, 2005 4:10 pm Post subject:
Re: Mechanical design consulting - what's the going rate? |
|
|
In article <Rup8f.483851$x96.172515@attbi_s72>, "Pat" <pkelecy
(removethis)@insightbb.com> says...
| Quote: | Out of curiosity, is doing such CAD work over a terminal server connection,
such a VNC or Microsoft's RDC, a practical option (where Solidworks would be
running on the remote computer)? Although I'm sure it can be done, I'm not
sure what the user experience would be like. It would, however, keep all
the files together and avoid the need to ftp.
|
I think you could use a remote connection to check things, but I
wouldn't want to work that way. It's not the same as being there.
Most of my projects have been a small number of parts, but the
individual parts get large. FTP has been working well for me.
Matt |
|
| Back to top |
|
|
Sporkman
Guest
|
| Posted:
Fri Oct 28, 2005 4:10 pm Post subject:
Re: Mechanical design consulting - what's the going rate? |
|
|
Pat (and others), take a look at "Unison" file synchronization software
(http://www.cis.upenn.edu/~bcpierce/unison/). It's freeware, developed
by the University of Pennsylvania, and looks very interesting. I
haven't had a chance to try it out, but it looks like it could fill a
niche need for those of us who do remote collaboration often. It
appears to be at least somewhat similar to Availl
(http://www.availl.com) which touts itself as being appropriate
specifically for multi-site CAD collaboration, but which costs thousands
to connect even just two sites. I don't know whether even Availl really
does what it says it does (at least as well as it says it does it), but
it does appear as if this KIND of site mirroring and file
synchronization application may have some benefits worth considering.
If anyone has had experience with Unison in particular or any of the
other file synchronization applications out there in general I hope
they'll post something about their experiences.
'Sporky'
www.h2omarkdesign.com
Pat wrote:
| Quote: |
Thanks Matt and John for the additional information.
I agree that good communication and organization is important regardless of
the work arrangement, but probably even more so when working remotely.
I was particularly interested in the logistical issues of this - how well
ftp-ing large CAD files back and forth and keeping related designs
coordinated works in practice. Apparently well enough.
Out of curiosity, is doing such CAD work over a terminal server connection,
such a VNC or Microsoft's RDC, a practical option (where Solidworks would be
running on the remote computer)? Although I'm sure it can be done, I'm not
sure what the user experience would be like. It would, however, keep all
the files together and avoid the need to ftp.
Thanks again.
Pat |
|
|
| Back to top |
|
|
Pat
Guest
|
| Posted:
Fri Oct 28, 2005 4:10 pm Post subject:
Re: Mechanical design consulting - what's the going rate? |
|
|
"Ken" <kagrundey.no@spam.pella.com> wrote in message
news:4360f21c$1@usenet.ugs.com...
| Quote: | I am inexperienced in this type of thing, but additional questions I would
have would pertain to my liability in the design work such as: is it
necessary to have a PE stamp, do I need liability insurance to cover my @$$
if I or someone working for me makes a mistake or if the client is just a
litigious freak.
|
Definitely a consideration, especially if developing a consumer product.
Fortunately the end user is not the public, and nature of this project is
more R&D (which the customer understands) so this is less of an issue.
Pat |
|
| Back to top |
|
|
John Layne
Guest
|
| Posted:
Fri Oct 28, 2005 8:10 pm Post subject:
Re: Mechanical design consulting - what's the going rate? |
|
|
Pat wrote:
| Quote: | Thanks Matt and John for the additional information.
I agree that good communication and organization is important regardless of
the work arrangement, but probably even more so when working remotely.
I was particularly interested in the logistical issues of this - how well
ftp-ing large CAD files back and forth and keeping related designs
coordinated works in practice. Apparently well enough.
Out of curiosity, is doing such CAD work over a terminal server connection,
such a VNC or Microsoft's RDC, a practical option (where Solidworks would be
running on the remote computer)? Although I'm sure it can be done, I'm not
sure what the user experience would be like. It would, however, keep all
the files together and avoid the need to ftp.
Thanks again.
Pat
|
It would be impractical to work over TightVNC the screen refresh is not
acceptable for anything other than using it for design reviews, even
with a broadband internet connection. Besides my Spacemouse wouldn't work!
I use PDMWorks to control the logistics of working on large projects.
The site holding the master data has a dummy PDM account for each remote
user. The person controlling the master data logs in with one of the
dummy accounts and checks out data on behalf of the remote user this
data is then put on the ftp site for the remote user to download and
work with. After the remote user has completed a part / drawing assembly
it is uploaded to the ftp site and checked back into the vault with the
dummy account.
Obviously this is not entirely fail-safe if the remote user is working
in context to other parts that are being worked on there could be
problems. One person needs to have a clear picture of who is doing what
and how that relates to what someone else is doing. But these problems
are not insurmountable.
John Layne
www.solidengineering.co.nz |
|
| Back to top |
|
|
|
|
|
|
FAQ
Memberlist
Register
Profile
Log in to check your private messages
Log in